How to install your own network cable: tricks, tips and recommendations

If you are thinking of placing network cable in your home you should know that you can do it yourself saving a lot of money in the installation.We explain how to bring network cable to any point in your home and some tips and recommendations to follow.

There are several reasons that can promote us to bring network cable to different points of our house.Depending on where the router is located, Laredwi-Fi may not reach certain stays of our house, or even if it does not do it with enough power to stop a 4K movie in streaming or play online.Wi -Fi networks are very comfortable, but they can suffer interference, channel saturation, noise and bandwidths.

With the network cable we avoid Internet falls, which in certain areas of the country are relatively frequent and a problem for business or people who work remote.If we live in a multi -story house where we need the Internet in the attic or basement, if we want great power to watch streaming movies in an area away from the router or if we simply want the best possible quality internet in the entire whole, the network cable is the solution.

How to install our own network cable?

When installing network cable in our own home, we mainly have two options to take the cable to the desired point:

In both cases we will need a similar amount of cable (it is convenient to be quite left over in the purchase of cable, since it should not1 Gbps premises) as well as abundant RJ45 connectors, since they are the ones we are going to use for each ends of the cable.

Unless we have experience or be really skilled by peeling cables with scissors, it would be recommended that we acquire a crimpator, a tool specially designed for this task.The network cable has no less than eight little cables that we must then place in the connector.It is important to be precise and if we are going to place several connections we will grad out having a criminal at hand.It is normal to finish connections in connection boxes in the rooms by functionality and aesthetics.

If we have decided to take the cable inside the macaroni, arise of patience, acquire a good guide for cables and if possible, a special lubricant for wiring.If we do not get this lubricant, we must use Fairy dishwasher in abundance to help the guide move from box to box.The process is simple to understand, although sometimes the narrows or curves closed in the macarrón make it difficult to do:

1- Think carefully the route on which we are going to carry the cable, avoiding the turns and curves as much as the route is longer.What will give us the most problems is what we have to make many turns.

2- generously smear the tip of the guide with lubricant and introduce it from the nearest box in search of the next one that interests us most to follow the route.

3- Once the guide has arrived to the desired box, we must join the tip of the cable to the other end of the guide to be able to continue on his way.It is important that this union is strong so that it is released along the way (sometimes we have to really throw hard) but in turn, not prepare a bag of insulating tape around the very thick union, because this will go against thatThe cable has a good time.This union must also be lubricated, because if the union passes, it passes the rest of the cable.

4- If we will get the cable to reach the desired box we have to stretch until we get a few meters, release it from the guide and introduce the ends of the guide by the next macarrón hoping to have the same success as until now.

If on the contrary, we have decided to carry the cable outside the wall, we will not need a guide or lubricant, but if an important amount of staples, a hammer and a drill with a thick drill, probably from 10 or 8. the steps toFollow are equally simple, and in principle more comfortable to perform.

1- We must calculate the route carefully to think where we are going to take the cable.The normal thing is that we do it above the rolling, holding it with staples, because although there are some that have a hole parades from behind, they are designed to be used in the installation.Come on, we do not recommend starting rolled.

2- The way to move from room to room is to make a drill through the partition, if possible in an area of the discreet wall.We will need a drill and a drill thick enough to then pass the cable.

3- We must fix the cable by the rolle as we place it.We can use staples, which are placed with a hammer or also with glue, more discreet but that offers less support.We can also make a mix of both, placing staples only in the curves, which is where the cable offers more resistance, and sticking the areas where the cable is lying and straight.

Tools, materials and accessories to install our own network cable

Among these necessary tools, materials and accessories we will see that there are some essentials (cable, connection shots and plugs, essentially), others highly recommended (crimpator) and others that we will need depending on the method we have chosen to carry our network cable of apoint to another (guide and lubricant or drill, staples and cable).Let's go with some of these articles:

RJ45 Ethernet Network Cable

This RJ45 Redethernet cable has a length of 50 meters, and it comes known cables inside for the connections rodj45 also carries a nylon thread inside to add solidity and subtract mechanical load from the threads.The outer shirt is firm plastic.Its price at Amazon is 49.99 euros.

Ethernet connectors RJ45 Mr. Tronic 100

We will need RJ45 Ethernet connectors, and in Amazon we have these of the Marcamr.Tronic for 19.99 euros the package of 100 units, more than left over.They are resistant and unlike other models, it comes with transparent housing, which allows us to see if the cables that pass through them are in the right order before pressing them, something that will come very well from our rookie position.

Digitus Cat-6 connection taking

In the majority of rooms we must end a connection takeover of the Digitus Cat-6 brand by functionality (to connect several devices to the cable) and by aesthetics.It costs only 5.84 euros in Amazon Yes, suitable for the entry of horizontal cable (left/right) and also Tomas are turned 40 °, which facilitates the insertion of connection cables.

PASSHÍLOSElectraline Guide

This passhilos guide of Nylon has a length of 25 meters and a thickness of 3 mm.It is resistant and lasting, more than enough for sporadic uses as we are going to give it its price at Amazon is 11.96 euros.

Lubricant for cable laying

Although Fairy dishwasher can make us a similar function, the lubricant for the laying of the specific cable is less pringus and more efficient for this afternoon.It costs Amazon 15.60 euros. Without color, it does not cause stains and is easy to clean.

Crimpadora Fontey

This crimpator is a very complete tool that comes with five interchangeable inserts: A03B for non -isolated tecks of 1.5 - 6 mm² connections, A26TW for isolated and not isolated, terminals of 2 * 0.5 - 6 mm², A10 for notisolated terminals of 1.5 - 6.0 mm², A30J for isolated terminals of 0.5 - 6.0 mm², A35WF for non -isolated virolas of 10 - 35 mm².In Amazon it costs 36.99 euros.

Cable staples

This set of 100 staples for durable pe cable and anti -corrosion nails costs us at Amazon5.85 Eurosts are staples for 6mm thick cables and bald are 16 mm, enough to hold well.

Other outstanding offers

Do not miss the rest of prominent offers today: